PRODUCT

  1. FIRE SUPPRESSION SYSTEM
  2. ARGONITE
  3. FM 200
  4. NOVEC 1230
  5. CO2 FLOODING
  6. FOAM FLOODING
  7. DELUGE - HVWS / MVWS
  8. KITCHEN FIRE SUPPRESSION SYSTEM
  9. FIRE TUBE FIRE SUPPRESSION SYSTEM
  10. BUILDING MANAGEMENT SYSTEM
  11. FIRE FIGHTING
  12. DETECTION & ALARM SYSTEM
  13. ADDRESSABLE FIRE ALARM SYSTEM | VESDA | HSSD | FAAST | WIRELESS FIRE ALARM SYSTEM
  14. WATER LEAK DETECTION SYSTEM
  15. GAS LEAK DETECTION SYSTEM
  16. TEMPERATURE HUMIDITY MONITOR
  17. RODENT REPELLENT
  18. CCTV SYSTEM
  19. ACCESS CONTROL & TIME ATTENDENCE SYSTEM
  20. PUBLIC ADDRESABLE SYSTEM
  21. INTRUSION ( Burglar ) ALARM SYSTEM
  22. HOME AUTOMATION & VDP
  23. GUARD MONITORING SYSTEM

FIRE SUPPRESSION SYSTEM

This System is intended to prevent or extinguish fires automatically within seconds, where there is electrical or sensitive electronic equipment serving a critical operation, the loss of which would not only be the value of the equipment but also the cost of business interruption such as caused by damage to Server Room, Data storage room.

Safe ‘N’ Secure specializes in the design, installation, testing, commissioning & service of fixed fire fighting systems.

ARGONITE

Argonite has been developed to meet the demands from the industry for an environmentally friendly media. Argonite is non-toxic, non-corrosive, non-fogging and leaves no residue. Argonite meets the challenge from both the Montreal- and Kyoto protocol with no ozone depletion potential or global warming potential.

Argonite is tested and approved by regulatory bodies throughout the world, and is effective against fires in almost all combustible materials and flammable liquids.

Applications

Argonite systems are ideally suited to the protection of fixed equipment and plant. They are particularly applicable for high value risks where fi res can have devastating consequences way beyond the cost of damage and lost production.

System design

In a closed space, almost all fires are extinguished in less than 60 seconds when the oxygen concentration falls below 15%. The Argonite fire extinguishing system, based on a mixture of 50% Argon and 50% Nitrogen, reduces the oxygen concentration to a level acceptable to human exposure over short periods – thus eliminating the fire quickly and effectively without affecting personnel.

Knowing the size and complexity of the area to be protected, the fire hazard present and the requirements of the local approving authority, a dedicated computer programme is used to specify the size and geometry of the Argonite system hardware.

FM200 CLEAN AGENT SYSTEM

In response to the impending production phase out of Halon fire extinguishants, FM-200 ( Heptafluoropropane ) is a replacement for Halon 1301 in applications requiring a clean environmentally acceptable fire extinguishing agent, suitable for use in manned areas.

It is a colourless gas at standard conditions, exhibiting a boiling point of -16.4 Degree Centigrade. Through the use of properly designed equipment, FM-200 will mix well in a protected enclosure to provide a homogenous mixture in air. For fire suppression applications, FM-200 is super pressurized to achieve rapid discharge into the protected environment.

Technical Specification FM-200
Chemical Formula C3F7H
Ozone Depletion Potential 0
Molecular Weight 170.03
Boiling Point -16.4 Degree Cent
Critical Temperature 102 Degree Cent
Extinguishing Concentration ,Heptane Cup 5.8 %
Burner ( %by Volume )  
Vapour Pressure at 21 Degree C 68.8 psia

FM-200 works by physical action, the molecules absorb heat so that the temperature of the flame falls to a point below which it cannot propagate, and the fire is extinguished. The oxygen depleting effect is minimal as only small quantities of the gas are used.

CO2 FLOODING

Carbon dioxide (CO2) gas has been used as an extinguishing agent in fixed installations since the beginning of the twentieth century. NFPA-12 ( National Fire Protection Association ) Rules and BIS 6382 codes for design of such system are used as standards for CO2 extinguishing systems. These fire extinguishing installations are usually provided on premises where water and foam cannot be used. CO2 can be stored in high pressure seamless steel cylinders in liquid form with maximum filling ratio of 0.667 kg/liter of cylinder volume.

At atmospheric pressure and 21 Degree Cel. Temperature, 1kg of liquid CO2 vaporizes to occupy 560 liters. This means that in order to “ flood/inject” CO2 gas into an environment, causing volumetric reduction of oxygen gas concentration, a large quantity of CO2 gas can be effectively stored in liquid form in relatively small cylinder volume.

HOW THE CO2 HIGH PRESSURE SYSTEM WORKS

  • The high pressure system operates on efficient pneumatic principles.
  • Pneumatic pressure is used to open the valves and operate pressure switches, etc.
  • No wires, pulley, equalizers or falling weights are used in this system.
  • Operating parts are located internally, eliminating the need for bulky protective cages.
  • The typical system offers three independent means of actuation : (1) Automatic (2) Remote Manual (3) Direct Manual.

NOVEC 1230

Because its use concentration is much lower than its No Observable Adverse Effects Level (NOAEL), Novec 1230 fluid offers the widest margin of safety of any viable halon replacement available on the market today.

3M™ Novec™ 1230 Fire Protection Fluid Safety Margin
Agent Novec 1230 Halon 1301 HFC-125 HFC-227ea
Use Concentration 4-6% 5% 8.7-12.1% 7.5-8.7%
NOAEL3 10%4 5% 7.5% 9%
Safety Margin 67-150% Nil Nil 3-20%

One fire protection fluid. So many reasons to use it.

Here is the new standard for halon replacement. Novec 1230 fluid offers a long-term, sustainable technology that has the greatest margin of safety, the lowest GWP for halocarbon alternatives, and zero ozone depletion potential.

What is Novec 1230 fluid ?

Novec 1230 fluid is a fluoroketone — a proprietary 3M technology that offers a number of important advantages over conventional halon replacements.

How does it work ?

Extinguishing via its cooling effect, Novec 1230 fluid works as a gas, yet it is a liquid at room temperature. Because it is not stored or shipped from the factory in pressurized cylinders, Novec 1230 fluid is easy to handle and charge. Novec 1230 fluid systems allow for more efficient use of space, requiring about the same number of cylinders as conventional halocarbon agents.

Note: Industry standards require egress from a protected enclosure prior to system discharge.

FOAM FLOODING

The Foam Flooding Systems are similar to Water Mist fire suppression systems but use an expanding foam solution mixed with water to extinguish the fire.

Foam suppression systems are useful for companies which cannot afford the expensive tank and pump system to operate the sprinklers or for when there is a particularly high risk of high flammable liquid which may need cover.

Automatic or manual fire detection can be used to release a foam and water mixture which will expand on release of the agent and give a large fire rating cover without the need for large storage or pump tanks.

Applications

Foam systems protect virtually any hazard where flammable liquids are present. These hazards are common to a multitude of industries including Petrochemical, Chemical, Oil and Gas, Aviation, Marine/Offshore, Manufacturing, Utilities, Military, and Transportation.

Applications for a Foam Flooding System include oil and chemical storage cylos or tanks and areas which require sprinklers but without the expense of a tank and pumping system.

HIGH / MEDIUM VELOCITY WATER SPRAY SYSTEM

High velocity systems are often used to protect equipment that incorporate heavy or medium oils equipment such as transformers, circuit breakers, diesel engines and fuel oil storage tanks, turbo alternator lube oil systems and oil fired boilers.

The high velocity nozzles are specifically designed to discharge a jet of water at high speed. The water jet forms a cone of coarse spray of uniform density which is discharged over a defined area. The coarse spray is able to penetrate the flame zone and reach the surface of the burning oil. The turbulence created by the high velocity spray forms an oil-in-water emulsion on the surface of the oil that will not burn. This “emulsification” is the principal way the fire is extinguished, along with a cooling and smothering effect.

The shape of the spray cone, the fire area contacted and the water flow is all controlled by the nozzle specifications – the orifice size and the shape of the internal swirl plate – along with the water pressure and the orientation of the nozzle.

 

Medium velocity sprayers discharge a water spray of finely divided droplets at medium velocity. They are ideal for protecting hazards involving light oils where emulsification from high velocity sprayers is not possible. The fine spray has a high heat absorption rate so medium velocity sprayers are an effective method of protecting adjacent plant and structures from heat during a fire by providing a continuous cooling spray over the exposed surfaces. Keeping nearby equipment cool minimizes damage and reduces the risk of explosion.

Medium velocity sprayers can be used in combination with other fire fighting systems – dry chemical and foam can be used effectively under the discharge. The fine spray also works to dilute and disperse flammable vapors.

The sprayers use an external deflector to achieve the desired discharge angle and spray characteristics. Wormald engineers will select the correct sprayers with flow rate, discharge angle and droplet size to best suit your application. Medium velocity sprayers use water economically and so can be used for long periods if required.

KITCHEN FIRE EXTINGUISHING SYSTEM

KITCHEN FIRE SUPPRESSION SYSTEM

System Design

  • The Kitchen Fire Suppression System is designed to provide fire protection in hoods and ducts of cooking appliances for restaurants.
  • The basic system consists of wet agent tank enclosed in a cylinder mounting box, Temperature Sensors, Heat sensing cable, Control panel, Nozzles, piping, & water storage tank (opiional) etc.
  • The system provides automatic actuation with an option of being actuated manually through a remote manual pull station.
  • The system is also capable of shutting down other appliances on system actuation, if required.
  • Additional equipments such as remote manual pull station, mechanical and electrical gas valves, pressure switches, electrical switches & accessories such as alarms, warning lights, etc. can be integrated with the system.
  • As the fire is detected Control Panel activates the wet agent tank and wet agent is discharged extinguishing the fire.
  • Single and Multi Wei Agent tank system is available.

 

Components of Kitchen Fire Suppression System

 

Sr. No. Description
1 Heal Sensing Coble
2 Temperature Sensors
3 Manual Pull Station
4 Control Panel
5 Wet Chemical Agent Storage
6 Water Storage Tank
7 Gas Supply Auto Shut Off Valve
8 Non Return Valve
9 Discharge Nozzle
10 Discharge Line

FIRE TUBE FIRE SUPPRESSION

FIRE TUBE FIRE SUPPRESSION SYSTEM FOR PANELS & MACHINES

ARGONITE

Argonite has been developed to meet the demands from the industry for an environmentally friendly media. Argonite is non-toxic, non-corrosive, non-fogging and leaves no residue. Argonite meets the challenge from both the Montreal- and Kyoto protocol with no ozone depletion potential or global warming potential.

Argonite is tested and approved by regulatory bodies throughout the world, and is effective against fires in almost all combustible materials and flammable liquids.

Applications

Argonite systems are ideally suited to the protection of fixed equipment and plant. They are particularly applicable for high value risks where fi res can have devastating consequences way beyond the cost of damage and lost production.

System design

In a closed space, almost all fires are extinguished in less than 60 seconds when the oxygen concentration falls below 15%. The Argonite fire extinguishing system, based on a mixture of 50% Argon and 50% Nitrogen, reduces the oxygen concentration to a level acceptable to human exposure over short periods – thus eliminating the fire quickly and effectively without affecting personnel.

Knowing the size and complexity of the area to be protected, the fire hazard present and the requirements of the local approving authority, a dedicated computer programme is used to specify the size and geometry of the Argonite system hardware.

FM 200 CLEAN AGENT SYSTEM

In response to the impending production phase out of Halon fire extinguishants, FM-200 ( Heptafluoropropane ) is a replacement for Halon 1301 in applications requiring a clean environmentally acceptable fire extinguishing agent, suitable for use in manned areas.

It is a colourless gas at standard conditions, exhibiting a boiling point of -16.4 Degree Centigrade. Through the use of properly designed equipment, FM-200 will mix well in a protected enclosure to provide a homogenous mixture in air. For fire suppression applications, FM-200 is super pressurized to achieve rapid discharge into the protected environment.

Technical Specification FM-200
Chemical Formula C3F7H
Ozone Depletion Potential 0
Molecular Weight 170.03
Boiling Point -16.4 Degree Cent
Critical Temperature 102 Degree Cent
Extinguishing Concentration ,Heptane Cup 5.8 %
Burner ( %by Volume )
Vapour Pressure at 21 Degree C 68.8 psia

FM-200 works by physical action, the molecules absorb heat so that the temperature of the flame falls to a point below which it cannot propagate, and the fire is extinguished. The oxygen depleting effect is minimal as only small quantities of the gas are used.

NOVEC 1230

Because its use concentration is much lower than its No Observable Adverse Effects Level (NOAEL), Novec 1230 fluid offers the widest margin of safety of any viable halon replacement available on the market today.

3M™ Novec™ 1230 Fire Protection Fluid Safety Margin
Agent Novec 1230 Halon 1301 HFC-125 HFC-227ea
Use Concentration 4-6% 5% 8.7-12.1% 7.5-8.7%
NOAEL3 10%4 5% 7.5% 9%
Safety Margin 67-150% Nil Nil 3-20%

One fire protection fluid. So many reasons to use it.

Here is the new standard for halon replacement. Novec 1230 fluid offers a long-term, sustainable technology that has the greatest margin of safety, the lowest GWP for halocarbon alternatives, and zero ozone depletion potential.

What is Novec 1230 fluid ?

Novec 1230 fluid is a fluoroketone — a proprietary 3M technology that offers a number of important advantages over conventional halon replacements.

How does it work ?

Extinguishing via its cooling effect, Novec 1230 fluid works as a gas, yet it is a liquid at room temperature. Because it is not stored or shipped from the factory in pressurized cylinders, Novec 1230 fluid is easy to handle and charge. Novec 1230 fluid systems allow for more efficient use of space, requiring about the same number of cylinders as conventional halocarbon agents.

Note: Industry standards require egress from a protected enclosure prior to system discharge.

CO2 FLOODING

Carbon dioxide (CO2) gas has been used as an extinguishing agent in fixed installations since the beginning of the twentieth century. NFPA-12 ( National Fire Protection Association ) Rules and BIS 6382 codes for design of such system are used as standards for CO2 extinguishing systems. These fire extinguishing installations are usually provided on premises where water and foam cannot be used. CO2 can be stored in high pressure seamless steel cylinders in liquid form with maximum filling ratio of 0.667 kg/liter of cylinder volume.

At atmospheric pressure and 21 Degree Cel. Temperature, 1kg of liquid CO2 vaporizes to occupy 560 liters. This means that in order to “ flood/inject” CO2 gas into an environment, causing volumetric reduction of oxygen gas concentration, a large quantity of CO2 gas can be effectively stored in liquid form in relatively small cylinder volume.

HOW THE CO2 HIGH PRESSURE SYSTEM WORKS

  • The high pressure system operates on efficient pneumatic principles.
  • Pneumatic pressure is used to open the valves and operate pressure switches, etc.
  • No wires, pulley, equalizers or falling weights are used in this system.
  • Operating parts are located internally, eliminating the need for bulky protective cages.
  • The typical system offers three independent means of actuation : (1) Automatic (2) Remote Manual (3) Direct Manual.

FOAM FLOODING

The Foam Flooding Systems are similar to Water Mist fire suppression systems but use an expanding foam solution mixed with water to extinguish the fire.

Foam suppression systems are useful for companies which cannot afford the expensive tank and pump system to operate the sprinklers or for when there is a particularly high risk of high flammable liquid which may need cover.

Automatic or manual fire detection can be used to release a foam and water mixture which will expand on release of the agent and give a large fire rating cover without the need for large storage or pump tanks.

Applications

Foam systems protect virtually any hazard where flammable liquids are present. These hazards are common to a multitude of industries including Petrochemical, Chemical, Oil and Gas, Aviation, Marine/Offshore, Manufacturing, Utilities, Military, and Transportation.

Applications for a Foam Flooding System include oil and chemical storage cylos or tanks and areas which require sprinklers but without the expense of a tank and pumping system.

HVWS / MVWS

High velocity systems are often used to protect equipment that incorporate heavy or medium oils equipment such as transformers, circuit breakers, diesel engines and fuel oil storage tanks, turbo alternator lube oil systems and oil fired boilers.

The high velocity nozzles are specifically designed to discharge a jet of water at high speed. The water jet forms a cone of coarse spray of uniform density which is discharged over a defined area. The coarse spray is able to penetrate the flame zone and reach the surface of the burning oil. The turbulence created by the high velocity spray forms an oil-in-water emulsion on the surface of the oil that will not burn. This “emulsification” is the principal way the fire is extinguished, along with a cooling and smothering effect.

The shape of the spray cone, the fire area contacted and the water flow is all controlled by the nozzle specifications – the orifice size and the shape of the internal swirl plate – along with the water pressure and the orientation of the nozzle.

Medium velocity sprayers discharge a water spray of finely divided droplets at medium velocity. They are ideal for protecting hazards involving light oils where emulsification from high velocity sprayers is not possible. The fine spray has a high heat absorption rate so medium velocity sprayers are an effective method of protecting adjacent plant and structures from heat during a fire by providing a continuous cooling spray over the exposed surfaces. Keeping nearby equipment cool minimizes damage and reduces the risk of explosion.

Medium velocity sprayers can be used in combination with other fire fighting systems – dry chemical and foam can be used effectively under the discharge. The fine spray also works to dilute and disperse flammable vapors.

The sprayers use an external deflector to achieve the desired discharge angle and spray characteristics. Wormald engineers will select the correct sprayers with flow rate, discharge angle and droplet size to best suit your application. Medium velocity sprayers use water economically and so can be used for long periods if required.

KITCHEN FIRE SUPPRESSION SYSTEM

System Design

  • The Kitchen Fire Suppression System is designed to provide fire protection in hoods and ducts of cooking appliances for restaurants.
  • The basic system consists of wet agent tank enclosed in a cylinder mounting box, Temperature Sensors, Heat sensing cable, Control panel, Nozzles, piping, & water storage tank (opiional) etc.
  • The system provides automatic actuation with an option of being actuated manually through a remote manual pull station.
  • The system is also capable of shutting down other appliances on system actuation, if required.
  • Additional equipments such as remote manual pull station, mechanical and electrical gas valves, pressure switches, electrical switches & accessories such as alarms, warning lights, etc. can be integrated with the system.
  • As the fire is detected Control Panel activates the wet agent tank and wet agent is discharged extinguishing the fire.
  • Single and Multi Wei Agent tank system is available.

Components of Kitchen Fire Suppression System

Sr. No. Description
1 Heal Sensing Coble
2 Temperature Sensors
3 Manual Pull Station
4 Control Panel
5 Wet Chemical Agent Storage
6 Water Storage Tank
7 Gas Supply Auto Shut Off Valve
8 Non Return Valve
9 Discharge Nozzle
10 Discharge Line

FIRE TUBE FIRE SUPPRESSION SYSTEM FOR PANELS & MACHINES

BUILDING MANAGEMENT SYSTEM

A Building Management System (BMS) or a (more recent terminology) Building Automation System (BAS) is a computer-based control system installed in buildings that controls and monitors the building’s mechanical and electrical equipment such as ventilation, lighting, power systems, fire systems, and security systems. A BMS consists of software and hardware; the software program, usually configured in a hierarchical manner, can be proprietary, using such protocols as C-bus, Profibus, and so on.

Features

  • Modern Architecture
  • Advanced Client Server Design
  • Multiple Site Management
  • Optimum System Capacity
  • Card Multi-Swipe functionality per cardholder
  • High Security Mode
  • Integrated Biometric Enrollment
  • Personalized disability privileges
  • Anti- Pass back

FIRE FIGHTING

Firefighting is the act of extinguishing fires. A firefighter suppresses and extinguishes fires to prevent loss of life, and/or destruction of property and the environment. Firefighters may provide many other valuable services to the community they serve, such as emergency medical services. Firefighting is a highly technical skill that requires professionals who have spent years training in both general firefighting techniques and specialized areas of expertise.

ABC STORED PRESSURE TYPE

A fire extinguisher, or extinguisher, is an active fire protection device used to extinguish or control small fires, often in emergency situations. It is not intended for use on an out-of-control fire, such as one which has reached the ceiling, endangers the user or otherwise requires the expertise of a fire department. Typically, a fire extinguisher consists of a hand-held cylindrical pressure vessel containing an agent which can be discharged to extinguish a fire.

Technical Specification

Size 1 Kg 2 Kg 5 Kg
Diameter 90 mm 110 mm 146 mm
Height 250 mm 300 mm 448 mm
Gross Weight 1.9 Kg 3.3 Kg 7.9 Kg
Discharge Time 6 Sec 6 to 12 Sec 12 to 15 Sec

SUPER CLEAN AGENT FIRE EXTINGUISHER

These Super Clean Agent Fire Extinguisherare made by using very high quality raw material, ensures high durability at its user end. These Clean Agent Fire Extinguisher are widely finds its valuable applications at various sectors.

We offer our clients an extensive range of Clean Agent Fire Extinguishers that is acclaimed among the clients for optimum quality and smooth performance. They are flammable in nature and are capable to cater the specific requirements in most effective manner.

CONVENTIONAL FIRE EXTINGUISHER

Dry Chemical Powder Type Fire Extinguisher

ABC dry chemical is usually a mix of monoammonium phosphate and ammonium sulfate, the former being the active one. The mix between the two agents is usually 40–60%, 60-40%, or 90-10% depending on local standards worldwide.

Note- NOT TO BE USE ON ELECTRICAL FIRES

Technical Specification

Capacity in Kg 5 10 25 50 75
IS Specification 2171 2171 10658 10658 10658
Jet Range (In Mtrs) 4-5 5-6 6-8 8-10 10-12
Discharge Time (In Secs) 15-20 25-30 25-30 40-50 50-60
Min Discharge Quantity 90% 90% 85% 85% 85%
Seal of Approval ISI ISI ISI ISI ISI
Hydraulic Tets Pressure of Cylinder 30 30 30 30 30

Water CO2 Type Fire Extinguisher

Water and Foam fire extinguishers extinguish the fire by taking away the heat element of the fire triangle. Foam agents also separate the oxygen element from the other elements.

Water extinguishers are for Class A fires only - they should not be used on Class B or C fires. The discharge stream could spread the flammable liquid in a Class B fire or could create a shock hazard on a Class C fire.

Note- NOT TO BE USE ON ELECTRICAL FIRES

Technical Specification

  Water CO2 Water CO2 Water CO2 Pressure
Capacity in Kg 9 50 9
IS Specification 940 13385 -
Jet Range (In Mtrs) 6 10 6-7
Discharge Time (In Secs) 60-120 60-180 60-90
Min Discharge Quantity 90% 95% 90%
Seal of Approval ISI ISI -
Hydraulic Tets Pressure of Cylinder 30 30 30

Mechanical Foam ( AFFF ) Type Fire Extinguisher

Foam has the ability to form an aqueous film which quickly over water-insoluble hydrocarbon fuel surfaces causing rapid fire extinguishment. Also it provides excellent penetrating and wetting qualities when used on class a fires. Hence, foam extinguishers are ideal for fires involving volatile liquids and freely burning materials.

Technical Specification

  Mech. Foam Mech. Foam Mech. Foam Store Pressure
Capacity in Kg 9 50 9
IS Specification 10204 13386 -
Jet Range (In Mtrs) 6 10 5-6
Discharge Time (In Secs) 60-90 60-180 80-90
Min Discharge Quantity 90% 90% 95%
Seal of Approval ISI ISI -
Hydraulic Tets Pressure of Cylinder 25 30 30

CO2 Type Fire Extinguisher

Carbon Dioxide (CO2) Fire Extinguishers are distinguished by a black coloured band around the top of the cylinder.

Carbon dioxide is a non-conductive and non-corrosive gas used to reduce the amount of oxygen available to the fire. Carbon dioxide is extracted from the atmosphere and stored at high pressure in the liquid state within a fire extinguisher.

Technical Specification

Capacity in Kg 2 3 4.5 6.5 9 22.5
IS Specification 2878 2878 2878 2878 2878 2878
Jet Range (In Mtrs) 2 2 2.5-3 2.5-3 2.5-3 2.5-3
Discharge Time (In Secs) 14-16 16-18 20-24 25-30 30-35 50-60
Min Discharge Quantity 98% 98% 98% 98% 98% 98%
Seal of Approval ISI ISI ISI ISI ISI ISI
Hydraulic Tets Pressure of Cylinder 250 250 250 250 250 250
Working Pressure (Kg/Cm2) 58-60 58-60 58-60 58-60 58-60 58-60

FIRE HYDRANT & SPRINKLER SYSTEM

Fire Hydrant & Sprinkler System

Fire Hydrant is a pipe that allocates water from a main location to the required place in order to control and reduce fire. The allocation of water is controlled by regulator. An Automatic Sprinkler provides a series of smaller pipelines and small holes which dispense water at the occurrence of fire. Fire Hydrants and Automatic Sprinkler System has become a common must have and one of the most important tool to control fire.

DETECTION & ALARM SYSTEM

We design and install the system as per the customer’s requirement. The above items are available in different makes namely - System Sensor, Apollo, Ravel, Morley, BOSCH etc.

In case of fire early detection of smoke and heat helps in fighting the fire effectively & extinguishing it in nascent stage. Thus preventing the fire from spreading and saving life and loss of property and business.

AUTOMATIC FIRE DETECTION & ALARM SYSTEM

In case of fire early detection of smoke and heat helps in fighting the fire effectively & extinguishing it in nascent stage. Thus preventing the fire from spreading and saving life and loss of property and business. It is a basic conventional system in which Fire Alarm Panel indicates the zone which has caught fire.

The system consists of following components

  • Fire Alarm Panel Starts from 2 zone, up to 24 zones
  • Detectors
  • Optical Smoke Detector
  • Heat Detector
  • Flame Sensor
  • Beam Detector
  • Intrinsically safe Ionization Detector
  • Intrinsically safe Thermal Detector
  • Manual Call Point
  • Hooter
  • Response Indicator
  • Cabling

We design and install the system as per the customer’s requirement. The above items are available in different makes namely - System Sensor, Apollo, Ravel, Morley, BOSCH etc.

Intelligent Addressable Fire Alarm System

This is advanced system in which control panel is capable of not only knowing the detector’s location accurately but also exactly how much smoke is in the chamber of the detector.

The system consists of following

  • Intelligent Fire Alarm Control
  • Addressable Detectors
  • Isolator Module
  • Loop driver card
  • Communication module
  • Modbus
  • Loop Addressable Sounder
  • Manual Call Point

Information on location of the fire, fault and system status can be easily displayed or printed in multiple locations. Integration to voice Evacuation systems, Paging systems and third party control systems is supported through a range of peripheral interface units.

Following approved makes are available - Morley –IAS, Notifier, Hochiki, GE Edward, Honeywell.

Wireless Fire Alarm System

Wireless Fire Alarm System is addressable and requires no cabling to be done and it indicates the accurate location of the detector fired.

The system consists of following

  • Wireless Fire Alarm Panel ( With range of 1-2 Kms., comes in 99 zones and 999 zones with programmable detectors )
  • Wireless Detectors
  • Radio Emitter – to transmit the signal
  • Wireless Manual Call Point

Features

  • NO wiring and conduiting, works on radio waves. Lot of concealed wiring is required in case of wired system.
  • Each detector works as an independent unit. So in case of non working of particular detector it does not have any effect on the system. But in case of Wired System Complete Zone / system becomes effected due to damaging of wire or failure of connection.
  • Zero maintenance and no AMC required. Where as AMC is must and tedious job in case of wired system.
  • Immediate installations, 200 nos. of detectors with panel can be installed in a single day even when building is occupied. Approximately 20 days are required in case of wired system.
  • Can be installed in running office complex / factory etc.
  • Complete flexibility. Any time there is a requirement for any modernization of the building. Any detector / panel can be shifted as per requirements.
  • Very – very competitive prices of Wireless Addressable Fire Alarm Panel. Wired panel with equal no.s of zones cost Five times more than the wireless panel.
  • Saving of cost from 10% to 60% at the time of installations and 90% saving in running cost.
  • Easy testing while every time it is practically not possible to test the system by generating smoke. A test button is available with each wireless smoke detectors and just pressing the button is sufficient for working of detector ,panel and emitter.
  • In case of non working / failure of main control panel in wired system, whole system will be held up. But the complete system will be working in case of non working of panel.

Information on location of the fire, fault and system status can be easily displayed or printed in multiple locations. Integration to voice Evacuation systems, Paging systems and third party control systems is supported through a range of peripheral interface units.

Following approved makes are available - Morley –IAS, Notifier, Hochiki, GE Edward, Honeywell.

Aspiration Smoke Detection System

The HSSD and VESDA are the internationally approved trade names for ASPIRATION SYSTEM. Aspirating Smoke Detection system (ASD) designed to give very early indication of an incipient fire condition. This pre-emptive warning – before the transition into the flaming and heat stages – provides the time necessary to take corrective action and avoid the danger, damage and disruption to operations that a fire can cause.

Aspirating Detection

The detector is mounted either inside or outside the area. It draws air from the protected area using an aspirating fan which is housed in the detection unit. The pipe network contains sampling holes at predetermined locations along the pipe network through which the air is LASER DIODE LIGHT SOURCE drawn.

Detectors can protect areas up to 2000 square metres to BS5839, or between 500 to 750 square metres to BS6266, in high air flow conditions. The pipework is configured in various ways according to the application.

Typically it will comprise a pipe network with sampling points at intervals similar to point detection. It can also, for example, be arranged to monitor across air handling units or in ducts.

Sampling pipe hart xl sampling points

  • Laser based particle counting – the superior technology
  • Elegant, compact, lightweight design
  • No particle filters required
  • No recalibration during lifetime of detector
  • Complete flexibility – four basic sub units provide installation options
  • On site sensitivity selection 0.0025%/m to 1%/m
  • LaserNet networking options
  • Modular design for fast and easy servicing
  • Configurable for integral or remote display options
  • Attachable power supply and battery back up unit
  • Individual pre-alarm and alarm levels

Standalone Smoke Detectors

Standalone smoke detectors are used for small areas such as small office, cabins, shops etc. It gives alarm from the unit in case of fire.

The system consists of following

  • Standby Current 10 μA
  • Alarm Current 30 μAT
  • Temprature Range 10-50 oC
  • Alarm Density 0.65-1.55 %FT
  • Alarm Volume 85dB in 3meter distance
  • ABS Fire resistance plastic case
  • Unit Box 10.8x114.4cm 0.20kgs
  • Carton 65x24x39cm GW - 21.00kgs

Beam Detection System

Beam detection system is ideal where the area to be protected is large , the height of ceiling is too much and where other smoke / heat detectors will be ineffective to install.

Features

  • Low cost protection of large areas
  • Very low maintenance
  • Quick and easy installation
  • Very minimum cabling required

Applications

  • Auditorium
  • Multiplex
  • Historic Building
  • Warehouse
  • Airports
  • Large Storage Areas
  • Shopping Malls
  • Hotel Atria
  • Museums

Beam Detector’s available in following brands – System Sensor, Fire Ray.

WATER LEAK DETECTION SYSTEM

Air conditioning, sprinklersystems, water cooledprocessors and heatingsystems are all potentialsources of water leakage which if undetected canseriously damage today's complex electrical, communication and computer networks even a small leak can prove disastrous.

To detect the water leakage the liquid sensing cable is installed below false flooring & above false ceiling. The control panel displays the location of the water detected by sensor cable.

An Intelligent and Addressable Sense Cable

Each sense cable is fitted with an electronic chip at one of its ends.

This manages the following functions -

  • Detects and localizes the leak of any liquid to the nearest metre along the length of the cable.
  • Addressable sense cable.
  • Detects and localizes any cut or interruption on the cable.
  • Digital transmission of all cable length data to the control digital unit.

GAS LEAK DETECTION SYSTEM

The systems detects the gas leak in the premises, pipes and protected areas. It sends signal to the panel and sounder / hooter is alarmed.

The system consists of following

  • Gas Leak Control Panel
  • Gas Leak Detectors
  • Manual Call Point
  • Hooters Cabling

Applications

  • LPG Storage
  • Chemical Industries
  • Gas Plant

TEMPRATURE HUMIDITY MONITOR

Temperature and humidity measurement is essential to taking control of your environment. Safe N Secure has a large variety of humidity testing and temperature monitoring devices. Choose from a selection of wireless temperature thermometers that provide data from up to 100 ft. away. For accurate readings in hard-to-reach and hazardous locations, choose an infrared thermometer with a bright laser for precise targeting.

Local Alert

A buzzer or hooter to alert the local personal incase the temperature reaches the critical level.

Auto Dialer

If the critical temperature is crossed then the auto dialer will dial to the pre programmed numbers and play the prerecorded message.

SMS

SMS will be sent to the pre programmed mobile numbers in case of an alert event.

Email

  • Daily email alerts and critical alerts can be sent.
  • Daily email alert will gives you hourly average temperature, peak and low temperature.
  • HumTemp software to configure the instrument, to generate reports.

Specification of Temperature Humidity Sensor

Humidity accuracy ±1.8%
Temperature accuracy ±0.3C
Temperature resolution ±0.01C
Humidity resolution ±0.03%
Temperature Range -40C to 123C
Humidity Range 0 - 100%

RODENT REPELLENT

Ultrasonic pest repellers are electronic devices that emit high-frequency sounds designed to repel, injure or kill household pests, such as rodents and insects. Whether they're actually effective at doing so has been disputed by testing labs and the U.S. Federal Trade Commission (FTC).

AUTOMATIC FIRE DETECTION & ALARM SYSTEM

In case of fire early detection of smoke and heat helps in fighting the fire effectively & extinguishing it in nascent stage. Thus preventing the fire from spreading and saving life and loss of property and business. It is a basic conventional system in which Fire Alarm Panel indicates the zone which has caught fire.

The system consists of following components

  • Fire Alarm Panel Starts from 2 zone, up to 24 zones
  • Detectors
  • Optical Smoke Detector
  • Heat Detector
  • Flame Sensor
  • Beam Detector
  • Intrinsically safe Ionization Detector
  • Intrinsically safe Thermal Detector
  • Manual Call Point
  • Hooter
  • Response Indicator
  • Cabling

We design and install the system as per the customer’s requirement. The above items are available in different makes namely - System Sensor, Apollo, Ravel, Morley, BOSCH etc.

Intelligent Addressable Fire Alarm System

This is advanced system in which control panel is capable of not only knowing the detector’s location accurately but also exactly how much smoke is in the chamber of the detector.

The system consists of following

  • Intelligent Fire Alarm Control
  • Addressable Detectors
  • Isolator Module
  • Loop driver card
  • Communication module
  • Modbus
  • Loop Addressable Sounder
  • Manual Call Point

Information on location of the fire, fault and system status can be easily displayed or printed in multiple locations. Integration to voice Evacuation systems, Paging systems and third party control systems is supported through a range of peripheral interface units.

Following approved makes are available - Morley –IAS, Notifier, Hochiki, GE Edward, Honeywell.

Wireless Fire Alarm System

Wireless Fire Alarm System is addressable and requires no cabling to be done and it indicates the accurate location of the detector fired.

The system consists of following

  • Wireless Fire Alarm Panel ( With range of 1-2 Kms., comes in 99 zones and 999 zones with programmable detectors )
  • Wireless Detectors
  • Radio Emitter – to transmit the signal
  • Wireless Manual Call Point

Features

  • NO wiring and conduiting, works on radio waves. Lot of concealed wiring is required in case of wired system.
  • Each detector works as an independent unit. So in case of non working of particular detector it does not have any effect on the system. But in case of Wired System Complete Zone / system becomes effected due to damaging of wire or failure of connection.
  • Zero maintenance and no AMC required. Where as AMC is must and tedious job in case of wired system.
  • Immediate installations, 200 nos. of detectors with panel can be installed in a single day even when building is occupied. Approximately 20 days are required in case of wired system.
  • Can be installed in running office complex / factory etc.
  • Complete flexibility. Any time there is a requirement for any modernization of the building. Any detector / panel can be shifted as per requirements.
  • Very – very competitive prices of Wireless Addressable Fire Alarm Panel. Wired panel with equal no.s of zones cost Five times more than the wireless panel.
  • Saving of cost from 10% to 60% at the time of installations and 90% saving in running cost.
  • Easy testing while every time it is practically not possible to test the system by generating smoke. A test button is available with each wireless smoke detectors and just pressing the button is sufficient for working of detector ,panel and emitter.
  • In case of non working / failure of main control panel in wired system, whole system will be held up. But the complete system will be working in case of non working of panel.

Information on location of the fire, fault and system status can be easily displayed or printed in multiple locations. Integration to voice Evacuation systems, Paging systems and third party control systems is supported through a range of peripheral interface units.

Following approved makes are available - Morley –IAS, Notifier, Hochiki, GE Edward, Honeywell.

Aspiration Smoke Detection System

The HSSD and VESDA are the internationally approved trade names for ASPIRATION SYSTEM. Aspirating Smoke Detection system (ASD) designed to give very early indication of an incipient fire condition. This pre-emptive warning – before the transition into the flaming and heat stages – provides the time necessary to take corrective action and avoid the danger, damage and disruption to operations that a fire can cause.

Aspirating Detection

The detector is mounted either inside or outside the area. It draws air from the protected area using an aspirating fan which is housed in the detection unit. The pipe network contains sampling holes at predetermined locations along the pipe network through which the air is LASER DIODE LIGHT SOURCE drawn.

Detectors can protect areas up to 2000 square metres to BS5839, or between 500 to 750 square metres to BS6266, in high air flow conditions. The pipework is configured in various ways according to the application.

Typically it will comprise a pipe network with sampling points at intervals similar to point detection. It can also, for example, be arranged to monitor across air handling units or in ducts.

Sampling pipe hart xl sampling points

  • Laser based particle counting – the superior technology
  • Elegant, compact, lightweight design
  • No particle filters required
  • No recalibration during lifetime of detector
  • Complete flexibility – four basic sub units provide installation options
  • On site sensitivity selection 0.0025%/m to 1%/m
  • LaserNet networking options
  • Modular design for fast and easy servicing
  • Configurable for integral or remote display options
  • Attachable power supply and battery back up unit
  • Individual pre-alarm and alarm levels

Standalone Smoke Detectors

Standalone smoke detectors are used for small areas such as small office, cabins, shops etc. It gives alarm from the unit in case of fire.

The system consists of following

  • Standby Current 10 μA
  • Alarm Current 30 μAT
  • Temprature Range 10-50 oC
  • Alarm Density 0.65-1.55 %FT
  • Alarm Volume 85dB in 3meter distance
  • ABS Fire resistance plastic case
  • Unit Box 10.8x114.4cm 0.20kgs
  • Carton 65x24x39cm GW - 21.00kgs

Beam Detection System

Beam detection system is ideal where the area to be protected is large , the height of ceiling is too much and where other smoke / heat detectors will be ineffective to install.

Features

  • Low cost protection of large areas
  • Very low maintenance
  • Quick and easy installation
  • Very minimum cabling required

Applications

  • Auditorium
  • Multiplex
  • Historic Building
  • Warehouse
  • Airports
  • Large Storage Areas
  • Shopping Malls
  • Hotel Atria
  • Museums

Beam Detector’s available in following brands – System Sensor, Fire Ray.

WATER LEAK DETECTION SYSTEM

Air conditioning, sprinklersystems, water cooledprocessors and heatingsystems are all potentialsources of water leakage which if undetected canseriously damage today's complex electrical, communication and computer networks even a small leak can prove disastrous.

To detect the water leakage the liquid sensing cable is installed below false flooring & above false ceiling. The control panel displays the location of the water detected by sensor cable.

An Intelligent and Addressable Sense Cable

Each sense cable is fitted with an electronic chip at one of its ends.

This manages the following functions -

  • Detects and localizes the leak of any liquid to the nearest metre along the length of the cable.
  • Addressable sense cable.
  • Detects and localizes any cut or interruption on the cable.
  • Digital transmission of all cable length data to the control digital unit.

GAS LEAK DETECTION SYSTEM

The systems detects the gas leak in the premises, pipes and protected areas. It sends signal to the panel and sounder / hooter is alarmed.

The system consists of following

  • Gas Leak Control Panel
  • Gas Leak Detectors
  • Manual Call Point
  • Hooters Cabling

Applications

  • LPG Storage
  • Chemical Industries
  • Gas Plant

TEMPERATURE HUMIDITY MONITOR

Temperature and humidity measurement is essential to taking control of your environment. Safe N Secure has a large variety of humidity testing and temperature monitoring devices. Choose from a selection of wireless temperature thermometers that provide data from up to 100 ft. away. For accurate readings in hard-to-reach and hazardous locations, choose an infrared thermometer with a bright laser for precise targeting.

Local Alert

A buzzer or hooter to alert the local personal incase the temperature reaches the critical level.

Auto Dialer

If the critical temperature is crossed then the auto dialer will dial to the pre programmed numbers and play the prerecorded message.

SMS

SMS will be sent to the pre programmed mobile numbers in case of an alert event.

Email

  • Daily email alerts and critical alerts can be sent.
  • Daily email alert will gives you hourly average temperature, peak and low temperature.
  • HumTemp software to configure the instrument, to generate reports.

Specification of Temperature Humidity Sensor

Humidity accuracy ±1.8%
Temperature accuracy ±0.3C
Temperature resolution ±0.01C
Humidity resolution ±0.03%
Temperature Range -40C to 123C
Humidity Range 0 - 100%

RODENT REPELLENT

Ultrasonic pest repellers are electronic devices that emit high-frequency sounds designed to repel, injure or kill household pests, such as rodents and insects. Whether they're actually effective at doing so has been disputed by testing labs and the U.S. Federal Trade Commission (FTC).

SURVEILLANCE SYSTEM

Surveillance is the monitoring of the behavior, activities, or other changing information, usually of people for the purpose of influencing, managing, directing, or protecting them. This can include observation from a distance by means of electronic equipment (such as CCTV cameras), or interception of electronically transmitted information (such as Internet traffic or phone calls) and it can include simple, relatively no- or low-technology methods such as human intelligence agents and postal interception.

ANALOGUE BASED CCTV CAMERA'S

Analogue Can record straight to a video tape recorder which are able to record analogue signals as pictures. If the analogue signals are recorded to tape, then the tape must run at a very slow speed in order to operate continuously. This is because in order to allow a three hour tape to run for 24 hours, it must be set to run on a time lapse basis which is usually about four frames a second. In one second, the camera scene can change dramatically.

The system consists of following

  • Camera
    • Dome
    • Box
    • PTZ – PAN, TILT & ZOOM
  • DVR ( Digital Video recorder )
  • Monitor / TV
  • Hooters Cabling

Note- Camera can be ( IR – Infrared- Night Vision ) or Day vision type.

IP CCTV CAMERA'S

An Internet protocol camera, or IP camera, is a type of digital video camera commonly employed for surveillance, and which, unlike analog closed circuit television (CCTV) cameras, can send and receive data via a computer network and the Internet. Although most cameras that do this are webcams, the term "IP camera" or "netcam" is usually applied only to those used for surveillance. The first centralized IP camera was Axis Neteye 200, released in 1996 by Axis Communications.

We provide customers end – to – end video solutions and components, including cameras, lenses, domes, keyboards, matrix, DVR’s, VCR’s, quads, Multiplexers and more.

Our trusted experience, combined with the quality and reliability of our integrated video systems, allows your customers to meet their existing and emerging security challenges. We offer complete systems that fit every budget for virtually any installation.

The brands available are Honeywell, Everfocus, Samsung, Panasonic, Capture, Act I, HIKvision, AVTechm.

ACCESS CONTROL & TIME ATTENDENCE SYSTEM

Access Control is the selective restriction of access to a place or other resource. The act of accessing may mean consuming, entering, or using. Permission to access a resource is called authorization.

Organizations of all sizes use time and attendance systems to record when employees start and stop work, and the department where the work is performed. However, it’s also common to track meals and breaks, the type of work performed, and the number of items produced. In addition to tracking when employees work, organizations also need to keep tabs on when employees are not working.

PROXIMITY CARDS & READERS

A proximity card or prox card is a "contactless" smart card which can be read without inserting it into a reader device, as required by earlier magnetic stripe cards such as credit cards and "contact" type smart cards. The proximity cards are part of the Contactless card technologies. Held near an electronic reader for a moment they enable the identification of an encoded number.

BIOMETRIC FINGER PRINT READER

Biometrics refers to metrics related to human characteristics. Biometrics authentication (or realistic authentication) is used in computer science as a form of identification and access control. It is also used to identify individuals in groups that are under surveillance.

Available Brands: HID Smart Card

PUBLIC ADDRESABLE SYSTEM

Whether you need a simple announcement Public Address instailation or integrated with Background Music, look to the cost-effective high quality range of Public Address System products from us. We offer products that can be combined to create perfect solutions for a wide range of PA applications. We have a complete range of PA loudspeakers, amplifiers, microphones and other professional audio accessories for a total solution.

P.A. System consists of

  • Mixing Amplifiers
  • Power Amplifiers
  • Microphones
  • Ceiling Speakers
  • In-wall Speakers
  • Column Speakers
  • Wall Mount Speakers
  • Box Speakers
  • Horn Speakers

INTRUSION ( Burglar ) ALARM SYSTEM

An intelligent system which will guard all your doors and windows, will raise an alarm in case of an emergency and call your family and friends for help. The purpose of the system is to protect the premises ( home, office, factory, showroom, shop etc. ) from burglary and intrusion – TOTALLY. This is achieved by installing various security sensors at all entry points of the premises.

These devices are then linked up to the heart of the system – the Control Panel. The Control Panel monitors all doors, windows and other entry points through the connected devices. In the event of an unauthorized entry, the system is triggered and an alarm is immediately raised through powerful sounders.

Fire detectors can also be attached to the Control Panel to detect fire. An inbuilt or attached speech dialer will call you, your friends, your family, the police, the fire brigade and anyone else you would like notified, in case of an emergency and deliver an intrusion or fire message recorded in your very own voice.

Home Automation & Video Door Phone

HOME AUTOMATION

In recent times residential construction has grown rapidly. It is hard to tell the difference from one residential project to another. Almost all are the state of the art construction. Almost all are in prime locations and almost all provide the best amenities and facilities.

Home owners today look for not just quality of housing but also for quality of life. Cutting edge technology providing security, convenience and comfort is a primary driver of higher quality of life.

Today such solutions are also available in India. The security system required for an integrated township, multi – apartment complex or stand alone home can have multiple combinations of features across security, convenience and comfort.

VIDEO DOOR PHONE

The video door phone is a screening device which allows you to identify and communicate with visitors at your door. Once you can see and speak to the person that wants to come in to your home, you can open the door with confidence and without the fear of being attacked. You can also attach an electronic lock to the video door phone and unlock the door by simply pressing a button.

The Video Door Phone consists of an indoor monitor and an outdoor camera unit. The indoor monitor has a microphone and speaker for two way audio communication, a black & white or colour monitor to view your visitor and 4 illuminated control buttons. It is installed inside your home. The outdoor camera unit also has a microphone and speaker, a black & white or colour camera and a bell button. It is installed outside your main door or gate, generally where the doorbell is installed. Visitors arriving at your front door or gate press a bell button on the outdoor camera unit which will sound a bell on the indoor monitor and the image from outdoor camera appears on your indoor monitor. You can then see and talk to the visitors and decide whether you wish to let them in.

GUARD MONITORING SYSTEM

The employee carries a reader which is activated at each checkpoint. The checkpoints can consist of Station Tags. During the patrol the reader stores the serial number of the checkpoint with the date and the time. Once completed, the information is downloaded from the reader into a computer where the checkpoints serial number will have an assigned location ( i.e. Main Gate, Backside Gate etc.) The reader can also be programmed to ignore duplicate checkpoint activations that occur sequentially or with in a certain time period. Computer software used to compile the data from the reader can print out reports that pinpoint the missed checkpoints or patrols. Then the administrator doesn’t have to review all the data collected.